Echelon
LumInsight Provisioning Tool ReadMe
Release 1.10.008, April 18,
2016
Copyright © 2015-2016 Echelon
Corporation
All Rights Reserved
The latest version of this file can be located at http://downloads.echelon.com/support/downloads/software/luminsight/lpt/1.10.008/ReadMe.htm.
LumInsight Provisioning Tool is the required tool for provisioning a LumInsight-based control network. It adds control devices to the Echelon SmartServer prior to the system becoming managed by LumInsight.
This document describes the known problems and workarounds for LumInsight Provisioning Tool. For additional information and updates (including critical updates), go to www.echelon.com/downloads. For answers to frequently asked questions, see Echelon’s Knowledge Base at www.echelon.com/support/kb. For the latest LumInsight news, go to www.echelon.com.
5 Installing LumInsight Provisioning Tool 1.10
6.1 Improvements in LumInsight Provisioning Tool 1.10
6.2 Improvements in LumInsight Provisioning Tool 1.01
7.1 Fixes in LumInsight Provisioning Tool 1.10
7.2 Fixes in LumInsight Provisioning Tool 1.01
8 Known Problems and Workarounds
The following are the LumInsight Provisioning Tool releases in reverse chronological order.
Name |
Number |
Date |
LumInsight Provisioning Tool |
1.10 |
Apr 2016 |
LumInsight Provisioning Tool |
1.01 |
Feb 2016 |
LumInsight Provisioning Tool |
1.00 |
Dec 2015 |
Following are the system requirements for computers running LumInsight Provisioning Tool:
· MicrosoftÒ Windows Server 2012 (64-bit), Windows 10 (64-bit and 32-bit), Windows 8.1 (64-bit and 32-bit), and Windows 7 (64-bit and 32-bit).
· 500 MHz processor or faster (2 GHz or faster processor recommended).
· 2 GB or more of free disk space.
· 2 GB RAM minimum.
· 1,024 x 768 or higher resolution display.
You can update any prior release of LumInsight Provisioning Tool to LumInsight Provisioning Tool 1.10 by installing the LumInsight Provisioning Tool download image. Prior releases are listed in the table in the Release Identification section above.
Note that if you upgrade to 1.10 from 1.00, then you may observe that certain object names that were permitted in 1.00 are no longer permitted in 1.10. For example, special characters other than underscore and hyphen are not allowed. Also, names are now limited in length.
You must also update any SmartServers used with LumInsight Provisioning Tool to the latest OLS version. The image and instructions can be found here: http://www.echelon.com/software-downloads?ele=153-0595-01A
The following table shows the notable improvements in this release:
Names can now be edited. |
The following table shows the notable improvements in this release:
N/A
The following table shows the notable improvements in this release:
The tool now properly handles updating the SmartServer versus provisioning a completely different one (e.g., a replacement). |
The following table shows the notable improvements in this release:
N/A
In some cases, the "sync" operation will result in a reboot dialog that ends up hidden behind other dialogs. The workaround is to minimize all top level windows until the reboot dialog appears.
Certain operations such as assigning devices to a group controller and binding devices to a TOS device are limited to 150 devices.
Echelon, LON, the Echelon logo and LonWorks are trademarks of Echelon Corporation that may be registered in the United States and other countries. For a complete list of registered trademarks see the Echelon website at www.echelon.com. All Rights Reserved.
Other trademarks belong to their respective holders.